
| Part | What it does | Typical size |
|---|---|---|
| Toe kick | Recess at the foot of base cabinets for your toes | About 4 inches high and 3 inches deep |
| Toe kick skin | Finished board covering the toe kick | Matches or contrasts with the cabinets |
| Filler | Strip closing a gap so doors and drawers clear walls and appliances | Narrow, sized on site or on the drawings |
| Scribe | Thin strip shaped to an uneven wall or ceiling | Small profile, cut to fit |
| Finished end panel | Covers an exposed cabinet side | Matches the doors or finish |
| Appliance panel | Covers a panel-ready fridge or dishwasher | Sized to the appliance |
| Crown molding | Trim at the top of wall cabinets | Sized to the ceiling and cabinet height |
| Light rail | Trim under wall cabinets that hides under-cabinet lights | Small profile |
What are the parts of the cabinet box?
The box, also called the carcass or case, is the structure everything else hangs on.
- Sides (sometimes called gables). The two vertical panels.
- Bottom, or deck. The panel the contents sit on.
- Top or stretchers. Base cabinets often use front and back rails instead of a full top, because the countertop covers it. Wall cabinets have a full top.
- Back. Closes the rear of the box and keeps it square.
- Hanging rail or nailer. A solid strip at the back for screwing the cabinet to the wall studs.
- Shelves. Adjustable shelves rest on pins in drilled holes; fixed shelves are joined into the sides.
Our boxes are plywood: 3/4-inch on frameless, and 1/2-inch behind a solid face frame on framed, with 3/4-inch available.
What is on the front of a cabinet?
The face frame (framed cabinets only)
A frame of solid wood across the front of the box.
- Stiles are the vertical members.
- Rails are the horizontal members.
- A mullion is a centre upright dividing an opening, for example between a pair of doors.
Frameless cabinets have no face frame; the front edges of the box are covered with edge banding. See frameless and face frame compared.

Doors
- Five-piece doors have two stiles, two rails and a centre panel. A Shaker door is the classic example.
- Slab doors are one flat piece, common in modern kitchens.
A door has its own stiles and rails, a panel, and a profile: the shape cut into its edges.
Drawers
- Drawer front. The visible face, matching the doors.
- Drawer box. The box behind it: front, back, two sides and a bottom. Dovetail joints are the strongest common method, and ours are full-extension dovetail drawers.
- Slides. The hardware the drawer runs on, under the box or on its sides.
What hardware does a cabinet use?
- Hinges. Concealed hinges are standard. The cup sits in a 35mm hole bored into the back of the door, and the mounting plate fixes to the box side or face frame.
- Slides. Full-extension and soft-close on better cabinets.
- Shelf pins. Small pins that hold adjustable shelves.
- Pulls and knobs. Pulls are measured centre to centre between the screw holes.
- Leg levellers. Adjustable feet some cabinets stand on instead of a built-in toe kick base.
What are the common cabinet types called?
- Base cabinet. Sits on the floor. Typically 34-1/2 inches tall and 24 inches deep, so with a 1-1/2-inch countertop the work surface lands around 36 inches.
- Wall (upper) cabinet. Hangs on the wall, typically 12 inches deep, in heights such as 30, 36 and 42 inches.
- Tall cabinet. A pantry or oven cabinet.
- Sink base. A base cabinet with a false front at the top instead of a drawer.
- Drawer base. A base cabinet with a stack of drawers.
- Corner cabinet. Blind corner, lazy Susan or diagonal designs that use the corner.
- Vanity. A bathroom base cabinet; see standard cabinet dimensions for the sizes.
What should I look for on cabinet drawings?
When you review shop drawings, these parts are all called out. Check the width, height and depth of every cabinet, where the fillers and end panels go, which way each door swings, the drawer sizes and what goes in each, and the appliance openings with their dimensions. Our drawings show all of it, and your designer walks through them with you before anything is built.
Frequently asked questions
What is the difference between a stile and a rail?
Stiles are the vertical pieces of a frame or door. Rails are the horizontal ones.
What is a false front?
A fixed panel that looks like a drawer front but does not open, used on sink bases where the plumbing is in the way. Some tip out for a sponge tray.
Do I need fillers?
Usually a few, at walls and appliances, so doors and drawers can open past handles and trim. Cabinets sized to your measurements need far fewer than standard sizes do.
What is a carcass?
Another name for the cabinet box itself.
Related reading
- Kitchen cabinet dimensions: standard sizes, and when custom beats them
- Framed vs frameless cabinets: the pros and cons of each
- Cabinet shop drawings: what they should show before your cabinets are built
- Inset vs full overlay cabinets: how the door sits, and why it matters
We build every kitchen in our Concord shop and ship it fully assembled, including to Tucson, AZ, Dallas, TX, Salem, OR and Sioux Falls, SD. See every city we deliver to.

Leave a Reply