Fitting custom cabinets in older homes: crooked walls, sloping floors and soffits

•

Navy blue pantry cabinets with butcher block counter, brass pulls and cream fish scale tile backsplash
Fitting custom cabinets in older homes: crooked walls, sloping floors and soffits
Older homes have walls that bow or lean, floors that slope and ceilings that are not level, so stock cabinets in fixed widths end in gaps and filler strips. Custom cabinets are sized to the room as measured and fitted with scribes and adjustable feet, so the runs follow the house instead of fighting it.
Get a fixed-price quoteSee recent kitchens
Common problems in older kitchens, and the fix
Problem What it does to cabinets The custom fix
Walls out of plumb Gaps behind or beside the run Scribe strips cut to the wall
Walls bowed Countertop and boxes will not sit flat Measure at three heights; build to the smallest
Sloping floor Run out of level Level from the high point; adjustable base
Uneven ceiling Gap above uppers varies Scribe or crown at the top
Soffits Uppers stop short Remove, or size uppers to sit under it

Why are older homes hard on kitchen cabinets?

Houses move. After 40, 60 or 100 years, walls bow and lean, floors settle and slope, and ceilings are rarely level. Earlier remodels add their own layers: a soffit hiding ductwork, a wall thickened with new drywall over old plaster. Stock cabinets come in fixed widths and assume square rooms, so in an older house they end in uneven gaps closed with filler strips and caulk.

How do you know if your walls are out of square?

  • Measure each wall at three heights. If the numbers differ, the wall bows or leans.
  • Check corners with the 3-4-5 rule. Mark 3 feet along one wall and 4 feet along the other; if the diagonal between the marks is 5 feet, the corner is square.
  • Hold a long level against the wall to see whether it leans out of plumb.
  • Run a level along the floor where the base cabinets will sit, and find the high point.

Our guide to measuring a kitchen for cabinets walks through every measurement.

Modern kitchen with navy flat-panel cabinets, oak open shelving and a wood island with marble counter
Cabinets and open shelving fitted wall to wall: built to the measured room, not to stock sizes.

How do custom cabinets fit crooked walls?

Custom cabinets are drawn after the room is measured, so each run is sized to the wall it sits on. Where a wall leans or bows, a scribe, a strip left slightly oversized and cut on site to follow the wall’s line, closes the gap cleanly. The result looks built into the house rather than pushed against it.

Get a fixed-price quoteSee recent kitchens

What about sloping floors?

Base cabinets are set level from the floor’s high point, then shimmed or adjusted along the run. A finished toe kick or base molding covers the difference at the low end. Plan for it in the drawings, so the countertop height works at both ends of the run.

What about uneven ceilings and soffits?

Uppers taken to an uneven ceiling are finished with a scribe or crown molding that follows the ceiling line. Soffits are a choice: if one is empty it can often come out, letting the cabinets run higher; if it hides ducts or pipes, custom uppers can be sized to sit neatly under it. See should kitchen cabinets go to the ceiling?

Navy kitchen with cabinets running to the ceiling, open oak shelving and a walnut island
Uppers taken to the ceiling: the top edge is planned to follow the ceiling line.

What should you plan for before ordering?

  • Open up first, measure second. If walls or soffits are coming out, measure after demolition, not before.
  • Find the rough-ins. Old plumbing and wiring rarely sit where a new layout wants them.
  • Decide on soffits early; they change every upper cabinet.
  • Ask for scribes and finished ends to be on the shop drawings, not improvised on site.

How does Crafted Cabinetry build for older homes?

Crafted builds across the East Bay, where many kitchens date from the 1970s to the 1990s. Every box is cut to your measurements in 1/16-inch increments, so runs fill the walls without filler strips, and scribes, panels and trim are drawn on the shop drawings before anything is cut. Outside the Bay Area, a third-party laser measure records the room as it really is, anywhere in the continental US, included in the quote. The cabinets are built in our Concord shop and delivered fully assembled.

Frequently asked questions

Do custom cabinets work in old houses?

Yes, and usually better than stock. They are sized to the measured room and fitted with scribes, so they follow walls that bow or lean.

How do you install cabinets on an uneven floor?

Set the base cabinets level from the floor’s high point and adjust along the run; a toe kick or base molding covers the difference.

What is a cabinet scribe?

A strip left slightly oversized and cut on site to follow an uneven wall or ceiling, closing the gap cleanly.

Should I measure before or after demolition?

After. Walls and soffits that come out change every measurement, so the final measure should be of the opened-up room.

Related reading

Get a fixed-price quoteSee recent kitchens

We build every kitchen in our Concord shop and ship it fully assembled, including to Lincoln, NE, Las Vegas, NV, Tacoma, WA and Omaha, NE. See every city we deliver to.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Privacy Policy